Flooring Installation, Refinishing & Epoxy — Serving Greater LA & the South Bay

Every Cal Coast floor starts below the wood. We grind, patch, and level concrete and plywood subfloors to a flat, sound base. A beautiful floor laid over a bad subfloor will telegraph every dip and squeak within a year.

It's the least glamorous step and the one that determines everything above it. We don't skip it, and we don't hide it inside a vague line item.

Tear-out is messy work, so we contain it. Plastic dust barriers seal the work zone from the rest of your home, and old material is hauled out and disposed of responsibly.

The result is a clean substrate to build on and a home that stays livable while we work, with no fine grit drifting into every room.

In condos, lofts, and multi-level homes, what goes under the floor matters as much as the floor itself. We install sound-rated underlayments and membranes that cut impact noise — footsteps, dropped objects, moving chairs — before it carries into the rooms below.

When your building or HOA sets IIC and STC requirements, we spec the assembly to meet them and document it for your building. A quiet floor is the kind of detail you only notice when it's missing.

We mill from a wide selection of premium unfinished lumber, so your floor is chosen for your space — species, plank width, and cut — instead of pulled off a shelf. We plan the first row so board widths stay even at walls and entries.

Every joint is staggered by hand for strength and a natural, pattern-free flow across the whole floor. Layout is mapped to your sightlines so the wood draws the eye exactly where it should.

Groove-and-peg is a traditional, handcrafted floor — wide planks with a defined groove between boards and decorative wood pegs set along the seams, the way floors were laid in early American and farmhouse homes. It reads as custom and old-world the moment you step into the room.

We set the pegs in a complementary or contrasting species — walnut pegs in white oak is a favorite — and ease the board edges for an authentic, hand-laid groove. Whether you want true face-pegged planks or simply the look, we lay it out to suit the room and the character of your home.

If your existing floors have enough thickness left, refinishing restores them for a fraction of replacement cost. We take the wood back to bare with a dustless sanding system that captures dust at the source.

Consistent texture across the whole floor is what makes color and coating land uniformly, edge to edge. It's the difference between a refinish that looks new and one that looks patched.

When the finish is dull and lightly scratched but the wood underneath is still sound, a buff and coat — also called a screen and recoat — refreshes the surface without a full sand-to-bare refinish. We abrade the existing finish so the new coat bonds, then lay down a fresh layer of protection.

It's a fraction of the cost and downtime of a full refinish, and kept on the right schedule it adds years between sandings. We'll tell you honestly whether your floor is a candidate — a buff and coat can't fix bare, gray, or water-stained wood, and we won't pretend it will.

Over the years, hard floors collect a film that mopping only moves around — old cleaner residue, wax buildup, and grime ground into the grain of the wood. We specialize in hard surfaces — hardwood, engineered, and luxury vinyl — deep-cleaning them to lift that buildup and bring the floor's true color and luster back.

Each surface gets the method it actually needs: pH-correct products and just the right moisture for wood — never the harsh water or steam that warps and dulls it. On hardwood, a thorough deep clean also makes ideal prep for a buff and coat.

Damaged, stained, or squeaking boards rarely mean tearing out the whole floor. We cut out the affected boards and weave in new ones — matched for species, grade, width, and grain — so the repair disappears into the surrounding floor.

From pet stains and water damage to a single cracked plank or a section lifted by a leak, we handle spot fixes and larger patches alike, then sand and finish the area to blend. Done right, you can't find where the old floor ends and the new begins.

When you want the look of wood with true waterproof performance, rigid-core vinyl plank and waterproof laminate deliver. They're a smart fit for kitchens, baths, laundry rooms, basements, and busy homes with kids and pets. We install click-lock floating systems over a clean, level, properly prepped base.

The result is a floor that stays quiet, tight, and flat for the long haul: no clicking underfoot, no hollow spots. That comes from leveling the base and laying the right underlayment before the first plank goes down.

For the most solid result underfoot, we set luxury vinyl plank and tile in a full-spread adhesive bond instead of floating it. Glued-down floors feel solid, won't shift or gap, and stand up to rolling loads and heavy traffic that floating systems can't.

That solidity is earned before the adhesive is spread: we moisture-test the slab and bring it clean, dry, and dead-flat first. Get that right and the bond holds for decades, not years.

For commercial spaces that need a seamless, sanitary, water-tight floor, we install sheet vinyl with heat-welded seams, the standard in healthcare, labs, schools, and commercial kitchens. Welding fuses the sheets into one continuous surface with no seams for water or bacteria to collect in.

We can carry the material up the wall as integral cove base, removing the dirt-trapping joint where floor meets wall. The result wipes down fast and holds up to the hygiene standards these spaces are held to.

For garages, shops, and showrooms that take real abuse, a full-broadcast flake system delivers a tough, textured surface that hides dust and tire marks while it works. We broadcast color flakes to full coverage, then lock them under a clear wear coat built for traffic.

A coating is only as good as the concrete under it, so our crews handle prep in-house: diamond-grinding the slab and moisture-testing it before anything is poured. That groundwork is what keeps a coating bonded for years instead of peeling in sheets.

Metallic epoxy is poured, not painted. Metallic pigments move through self-leveling resin to create depth and movement no two floors share — a statement surface for showrooms, retail, offices, and rooms that deserve one.

We work the pour by hand to direct the pattern, then seal it under a clear topcoat for protection and shine. Because every pour is one of a kind, we sample colors with you before installation day — what you approve is what gets poured.

Micro-cement isn't an epoxy — it's a hand-troweled cementitious overlay, applied in thin coats for a seamless, stone-like finish with no grout lines. It's the surface behind modern minimalist interiors: matte, continuous, and quietly dramatic.

At only a few millimeters thick, it goes over concrete, tile, or existing floors without demolition, then gets sealed for water and stain resistance — one uninterrupted surface that runs the length of a space.

A handrail is the part of a staircase you put your hand on every day, so we build and finish it to be as solid as it is good-looking. We craft newel posts, balusters, and handrail profiles in wood matched to your floors — or pair warm wood rails with wrought-iron balusters for a more open, modern line.

Whether we're installing a new railing or refinishing an existing one to match freshly redone floors, every run is built to code, with a graspable profile, proper height, and baluster spacing that meets safety requirements. The result is a rail that feels right in the hand and ties the staircase into the rest of your home.

Stairs are where a floor turns into a feature. We fabricate treads, risers, and skirt boards from the same species and finish as your floors, with custom nosings and edge profiles cut to match — so the staircase grows out of the floor instead of interrupting it.

Whether we're cladding an existing staircase or building treads up from the stringers, each piece is milled to your exact rise and run and fitted on site — mitered returns, bullnose or square nosings, open or boxed ends. It's furniture-grade joinery, built in the shop and fitted in your home.

We finish with the systems professionals trust: hardwax-oils like Rubio Monocoat and WOCA for a natural, repairable matte, and polyurethanes like Bona and Loba for hard-wearing protection in high-traffic homes.

We recommend the right finish for how your floor will actually be lived on, not the most expensive one. See the trade-offs in The Finish Collection.